The business of pressure washers relies greatly on the equipment they use. Pump repair is a critical process that needs special attention. The process is relatively easy given enough knowledge of the person doing it. If you want to lessen the necessary repair, then maintenance is the key. The two common types of industrial grade pumps are General and Cat. General is the most popular in terms of sale while Cat leads in terms of suction power for it is said that it can suck better in plastic containers.
The pump is connected to the engine and its power comes from the two parallel belts. The pump needs water to function properly so turn off the engine if you see that there is no more water in the pump. Another important element you should take note of is the oil in the pump. Change the oil as frequently as once a month to ensure efficient output for the machine.
The valves inside the pump should be replaced often, after 300 to 500 hours of use would be ideal. Just remove the bolt holding the valve and take out the valve itself. Put in the new valve and then bolt it again. Wrench the bolt tightly afterwards.
Drain the oil and see whether you have a problem. If the oil looks the same, then you are safe. If it has bubbles or if it turned white, then there are two things that might have caused this. Overheating is one cause and a ***** is another.
Make sure that the belt is fitted tightly and fitted well. If you notice any drips, make the appropriate actions to repair the damage. Usually, a Teflon tape is all it needs. This will stop the leak and prevent any rust as well. Teflon is easy to remove as well if ever you need refitting in the future.
Low pressure inside the pump is one of the most common pump repair problems. There are a multitude of reasons that may cause this. Among these reasons include faulty water supply, leakage in the hose, belt slippage, worn out gun nozzle tip, slow engine rpm, faulty pressure gauge, malfunctioning spray nozzle tip and dirty inline filter.
Since your machine is the one that brings in the money, you have to make it your business as well as to check it regularly for little damages and future repairs. Sometimes, all you have to do is listen to the pumps. If it is making too much noise then it may be time to check the air suction line, bearings and the valves.
It is the job of the pressure washing contractors to know the ins and outs of pump repair and maintenance. Those discussed here are only the tip of the iceberg. If you are not knowledgeable in the area, better seek the assistance of the experts so any damage done will be corrected in time for business.
More...
The pump is connected to the engine and its power comes from the two parallel belts. The pump needs water to function properly so turn off the engine if you see that there is no more water in the pump. Another important element you should take note of is the oil in the pump. Change the oil as frequently as once a month to ensure efficient output for the machine.
The valves inside the pump should be replaced often, after 300 to 500 hours of use would be ideal. Just remove the bolt holding the valve and take out the valve itself. Put in the new valve and then bolt it again. Wrench the bolt tightly afterwards.
Drain the oil and see whether you have a problem. If the oil looks the same, then you are safe. If it has bubbles or if it turned white, then there are two things that might have caused this. Overheating is one cause and a ***** is another.
Make sure that the belt is fitted tightly and fitted well. If you notice any drips, make the appropriate actions to repair the damage. Usually, a Teflon tape is all it needs. This will stop the leak and prevent any rust as well. Teflon is easy to remove as well if ever you need refitting in the future.
Low pressure inside the pump is one of the most common pump repair problems. There are a multitude of reasons that may cause this. Among these reasons include faulty water supply, leakage in the hose, belt slippage, worn out gun nozzle tip, slow engine rpm, faulty pressure gauge, malfunctioning spray nozzle tip and dirty inline filter.
Since your machine is the one that brings in the money, you have to make it your business as well as to check it regularly for little damages and future repairs. Sometimes, all you have to do is listen to the pumps. If it is making too much noise then it may be time to check the air suction line, bearings and the valves.
It is the job of the pressure washing contractors to know the ins and outs of pump repair and maintenance. Those discussed here are only the tip of the iceberg. If you are not knowledgeable in the area, better seek the assistance of the experts so any damage done will be corrected in time for business.
More...